Posts Tagged ‘Red Bank’

« Older Entries

Plainsboro Heating Tip: Dangers of Not Changing Your Furnace Filter on Time

Wednesday, March 21st, 2012

Of the many ways to heat a home in Plainsboro, forced air systems are the simplest in function and the easiest to maintain.  They are so simple, in fact, it is easy to forget they need attention at all, but there are dangers to not changing your furnace filter on time that have a real and painful cost in efficiency and dollars.  Even health risks arise when filters have been neglected too long.

Contracting with a company like Heritage Air & Heat ensures consistent maintenance and oversight to allow home owners the comfort and relaxation you deserve in your own home.

Back to Basics

Usually in the basement or a central location, a furnace heats air to a temperature set by the thermostat.  Over the years, technological improvements have enabled furnaces to be much smaller and fit into closets instead of the large and gangly monsters of old that could fill an entire basement.

By a fan in the furnace, the warm air is circulated through filters into a system of ducts to be distributed to grates in the wall or registers on the floor.  A second grate and duct system returns cooler air back to the furnace to be reheated.

The Dangers of Not Changing the Filter

When the system is properly maintained, it is clean, efficient and produces comforting heat on demand at the touch of the thermostat or consistently throughout the day and night.

The furnace filter is designed to remove dust from air as it passes through your furnace. The longer your furnace filter is in place the dirtier it becomes. The increase of particles caught in the filter creates resistance to air flow through the filter and reduces efficiency.

To make up for the loss of flow through a dirty filter, the heat exchanger, usually a gas or oil fired flame, must work harder to produce the same amount of heat to the space.  This becomes costly financially and causes undo wear and stress on the equipment, requiring a partial or full replacement much sooner.

Additionally, operating above ideal designed conditions, cracks in the chamber may appear from the over load which can allow carbon monoxide, a toxic gas, to be released into the duct work.  This gas in large quantities in the home can cause headaches, nausea, and in extreme circumstances, even death.

Regular Maintenance

To avoid problems and excessive strain, remember to change the filters at the beginning of each new heating season.  An annual maintenance check-up and thorough cleaning by a qualified company like Heritage Air & Heat ensures a safe and comfortable season of warmth with no need to worry about the dangers of not changing filters in your Plainsboro furnace.

Tags: , , , , ,
Posted in Services | Comments Off

West Windsor Heating Repair Question: What Does a Furnace Thermocouple Do?

Wednesday, March 7th, 2012

Modern appliances are equipped with an array of safety measures to make sure that they operate safely in your West Windsor home. This includes gas furnaces, which are harmless when working correctly but can be unsafe if something goes wrong. Perhaps the most crucial safety feature of a gas furnace is the thermocouple, also called a flame sensor.

Essentially, a furnace thermocouple works as a kill switch to shut off the furnace in case the gas is not igniting, like if the pilot light is out. Here is how it works.

The thermocouple is made up of two pieces of metal which are welded together at one end, called the “hot end” because it actually sits directly in the path of the furnace flame. On the cold end, it is wired to a circuit. Under normal circumstances, when the furnace is switched on, gas flows through the line and is ignited by a pilot light, ignition spark or glow coil. The flame heats up the thermocouple, and the furnace stays on.

However, sometimes the gas may not ignite, for example if the pilot light is out or the glow coil is faulty. In these cases, if there were no thermocouple, gas would continue to flow out without being lit, creating a very dangerous, poisonous and potentially lethal situation.

What the thermocouple does is detect heat, so if the furnace is on, but the hot end of the thermocouple has not heated up, that circuit up at the cold end kills the power to the furnace so that gas cannot continue to flow out unchecked. That way, you do not have to worry about a gas leak building to dangerous levels without being aware of it.

Sometimes, the thermocouple can malfunction, causing the furnace to shut off even if the burners are working just fine. Usually that is just the result of build up on the hot end over time, which can be fixed with some sand paper or emery cloth. If you suspect a problem with your furnace’s thermocouple, give Heritage Air & Heat a call today!

Tags: , , , , , ,
Posted in Services | Comments Off

Hightstown HVAC Maintenance Guide: Things You Should Not Do Yourself

Friday, February 10th, 2012

Everyone wants to feel handy around their Hightstown house and there are a lot of great things you can do to help keep your home and its various systems in tip top shape, but not everything should be on your to do list. Some tasks are dangerous or require special equipment and should only be performed by professionals. Here is a list of some such tasks and why you should avoid them:

  • Service a Gas Appliance or Furnace – If it involves a gas line, call a professional. This goes doubly so for live electrical work. You should always call someone who has the specific certification and licenses needed to work on your gas or electricity systems. They know the safety precautions and if there is a problem they will recognize it immediately and act fast to keep everyone safe.
  • Annual Maintenance – Filter changes, cleaning and other small jobs can be on your to do list, but big time maintenance done annually on your exhaust pipes, furnace or air conditioner should be done by a professional who has the equipment for it.
  • Duct Cleaning or Patching – You can clean the vents and the entry lines at your air handler just fine, but how will you reach the middle of your ducts without an industrial strength vacuum and duct cleaning system? Patching is similarly hard without the right equipment.
  • Remodeling of a Room – Unless you have the necessary skills and know what permits are needed, heavy duty remodeling of a kitchen, bathroom or new room should be done by someone with plumbing certification and experience.
  • Sewer Line Service – Always call an expert for anything related to your sewer or drainage system. They are not only complicated, but tend to be directly connected to city property and require a permit to work on. Even if you don’t break anything, the legal implications of this work require professional help.

There are a lot of fun things you can do around your Hightstown home to keep it in good condition, but for the big stuff, always call Heritage Air & Heat – if not for the sake of your home, for your health and wellbeing.

Tags: , , , ,
Posted in Services | Comments Off

Point Pleasant: Basic Boiler Maintenance

Wednesday, February 1st, 2012

The boiler in your Point Pleasant home is a sensitive piece of equipment that needs routine maintenance and repairs. Regularly maintaining your boiler is especially important for safety reasons. Many boiler malfunctions and accidents are due to neglecting some of these basic tasks.

Even if you’ve just installed a new boiler, the safety valves and settings should be checked by a professional on a regular basis to prevent a breakdown or hazard. We recommend that you schedule a boiler inspection and cleaning at least once a year. Call Heritage Air & Heat if you have any questions about boiler maintenance.

A service technician will measure the pressure, drain and remove sediment buildup, test the efficiency ratings, and make sure your boiler is set at the right temperatures. Regular maintenance can also help you determine whether or not you need a boiler replacement. By keeping track of performance levels, you will be able to tell when it’s time for an upgrade.

Other tasks performed during an annual maintenance visit include cleaning and lubricating all the components, checking for any leaks or clogs, and testing gas boilers for any carbon monoxide intrusion. If you have any gas appliances in your home, you should always have carbon monoxide detectors and test them once a month.

Boiler pressure is something that you can check often on your own. If you aren’t sure how to read the pressure gauge, or if you aren’t sure what the right pressure should be, just call one of our technicians to walk you through this process.

Always call Heritage Air & Heat if you have any problems with the boiler in your Point Pleasant home. We are here to help and answer any questions you may have.

Tags: , , , , ,
Posted in Services | Comments Off

Lawrenceville HVAC Guide: Important Indoor Air Quality Tips When Remodeling

Friday, January 27th, 2012

Remodeling your Lawrenceville home is a big step. As you plan the layout of your new bathroom or the size of the bedroom being added to the second floor, make sure you take into account the effects your changes will have on the indoor air quality of your home. Here are some specific things to keep in mind:

  • Water and Moisture – When you build on to or remodel your home, one of the most common problems is excess moisture. The grade may not be built to handle the extra space or you may find that moisture is harder to block from your home than expected. However, it’s vital that any additions are as water tight as the original construction. Mold and mildew, as well as dust mites and other humidity and moisture borne pollutants are major health concerns.
  • Ventilate Properly – Most people assume that the best thing they can do is close their home up tightly to block out pollutants. But, indoor air can be as much as 100 times more polluted than outside air if it isn’t properly ventilated. Stagnant, stale air filled with dust, pollen and dander among other things is not healthy, so extend your ventilation system to support your new addition.
  • Proper Flooring – The floor you choose when remodeling has a major impact on indoor air quality. You want to ensure any water that gets on the floor, especially in bathrooms can be removed without it penetrating to the wood underneath. Properly sealed tiles and fixtures are a must.
  • Unsafe Building Materials – Modern materials are generally safe, but if your home was built before 1978, consider the risk of flaking paint or old insulation before you start demolishing a room for remodeling. Lead paint in window frames and doors can be a major risk if it flakes and enters the air and asbestos can be found in insulation in walls, wiring and pipes.

Remodeling is a big step, and likely you have a lot of things on your mind, but don’t forget to include the air quality in your calculations, both during and after the construction. The EPA has a fantastic resource on indoor air quality in home remodels to help you determine what things you should watch for in each room of the house as you make changes.

Tags: , , , ,
Posted in Services | Comments Off

Tinton Falls Heating Guide: Pros and Cons of Various Heating Systems

Wednesday, January 11th, 2012

When it comes time to install a new heating system in your Tinton Falls home, there are a lot of options to consider. Many people get overwhelmed when confronted with all of the furnaces, boilers and heat pumps on the market these days. So, to help you get a handle on what each has to offer and which will offer you the best benefits, here is an overview of the modern heating system market.

Furnaces

Furnaces are the core of a forced air heating system and use gas, oil or electricity to heat air which is then circulated through your home by a blower in your air handler. Furnaces are among the most fuel efficient heating systems on the market today with options available at up to 95% AFUE (meaning it uses up to 95% of the fuel consumed to produce heat). They are also inexpensive to install and while they don’t last quite as long as boilers, they are highly efficient when well cared for.

Boilers

Boilers use gas, oil or electricity to heat water or steam which is then circulated through your home into radiators or baseboard heaters. The heated water or steam releases heat into your home and heats it in turn. While not quite as energy efficient as a high efficiency furnace, boiler heat is perfect for homes with existing radiators and no room for vents and ductwork. It also has less of an impact on indoor air quality since there is no air movement and boilers tend to last a very long time when well maintained.

Heat Pumps

Heat pumps are becoming increasingly popular, especially in milder climates where it rarely gets below 40 degrees F. A heat pump uses the same technology as an air conditioner to extract heat from outside using a compressor, evaporator coils, and condenser coils with refrigerant.

It is most efficient in the spring and fall when temperatures are mild, but it uses much less energy than either a boiler or furnace and it can be used in the summer to cool your Tinton Falls home. When properly maintained, a heat pump will last 10-20 years and save quite a bit of money, though it is recommended that you have an emergency heat source for days when the temperature outside gets below 40 degrees F.

Tags: , , , , , , ,
Posted in Services | Comments Off

Red Bank Heating Guide: High Efficiency Furnaces and Chimney Concerns

Wednesday, December 21st, 2011

When upgrading to a high efficiency gas furnace in Red Bank, you may need to make some upgrades to your chimney. Older chimneys built for standard furnaces with normal exhaust needs are not built to the specifications needed by today’s high efficiency models. Not only is it unsafe to leave it as is, but the cost of repairs if you don’t have it upgraded can be substantial.

Down-Sizing

A common concern when upgrading to a high efficiency gas furnace is the issue of condensation and draft. Because the amount of exhaust being vented is reduced by a high efficiency furnace, your current setup is not sufficient for the new model. So, it needs to be reduced in size by a professional to avoid backup of exhaust. Proper chimney sizing is a complex process that requires professional guidelines and careful measurements of all appliances in your home.

Because the chimney often isn’t used at all for a high efficiency furnace (often PVC pipe used instead), the extra airflow in the chimney can become a major issue.

Chimney Condensation

The biggest concern for the chimney when changing the furnace efficiency is condensation. Specifically, acidic condensation droplets can build up in the chimney if not properly stopped. A new chimney liner must be placed in the chimney to avoid excessive corrosion due to the acid droplets. Keep in mind that the efficiency of your new furnace will determine whether you will use the traditional chimney for exhaust or if a new line will be installed to vent your furnace.

When to Take Action

If you have your furnace replaced, your technician will likely discuss the chimney situation in your home with you. Keep in mind that this might be necessary and that there might be an added cost involved because of it. Modern furnaces are not designed to accommodate aging chimneys and your safety and the integrity of your house are at risk if you don’t retrofit the chimney if necessary.

Tags: , , , ,
Posted in Services | Comments Off

Freehold HVAC Tip: Where to Place a Thermostat for Accurate Heating

Friday, December 16th, 2011

It’s easy to forget that with your furnace in the basement churning away all day to keep your Freehold home warm, but your thermostat is the single most important device in ensuring your home is heated to the temperature you want. If it stops working or it misreads the temperature inside your home, your furnace won’t know what temperature it actually is and will turn on and off at the wrong time.

Where Not to Place Your Thermostat

To avoid inaccurate readings, avoid placing your thermostat in the following locations:

  • Direct Sunlight – Direct sunlight will almost always increase the perceived temperature of the thermostat. Unless you live in a greenhouse, this will be very uncomfortable for everyone in your home.
  • Windows – Windows can result in direct sunlight and breezes. If the windows are not properly sealed, cold air can blow in and make it seem cooler in your home than it really is. In any of these cases, your thermostat will misread the indoor temperature.
  • Drafts – Drafts from improperly sealed doors, windows, or anything else in your home can negatively impact the thermostat.
  • Heat Vents – Don’t place your thermostat near a radiator or heat vent where it is likely to be warmer than anywhere else in the house.
  • Kitchens – Kitchens tend to be warmer than other rooms in the house, especially when in use. Avoid placing a thermostat here unless you have a zone control system and your kitchen is separate from other rooms.

A properly placed thermostat will ensure your home is heated or cooled to the temperature you desire regardless of outdoor conditions. If you’re unsure whether your thermostat is calibrated properly, check the temperature with a separate thermometer in a different location in the same room. If it is significantly warmer or cooler in one place than another, try to determine which is more indicative of the actual comfort level in your home. When properly located, your thermostat should never be an issue again.

Tags: , , , , ,
Posted in Services | Comments Off

How Heating Zone Control Can Save You Money in Brick

Wednesday, November 2nd, 2011

The costs of heating your Brick home have risen dramatically over the past couple of decades, thanks to higher energy costs and price increases for heating equipment. Despite the strides made in energy efficiency, there seems to be no end in sight for the steady rise in heating equipment operating costs.

Now add in the cost of heating unoccupied areas of your home, such as basements, hallways, or extra bedrooms, and the energy costs go even higher. Most of these costs are unnecessary and avoidable if you have the time and a small investment in a well-planned heating “strategy” for your home. This strategy involves using heating zone controls to make the most efficient use of your heating system.

In a nutshell, here is how heating zone control works. The rooms in your home are connected to your heating system by a series of ductwork, which carries heated and conditioned area to all corners. But some of these areas may not need to be heated as much – or possibly at all – compared to other rooms in your home. For example, do you need heat in your kitchen but not in your basement? Most people would answer yes. Or they may say they need more heat in the kitchen and some, but not very much heat in the basement.

Or try this: do most people in your house spend more time in one room, such as the family room, and less time in their bedrooms? If so, why would it be necessary to heat the bedrooms all of the time? In order to deliver heat to areas in your home that need it the most, the ductwork to these rooms should always be “open.” Ductwork to other unused areas of your home can be “closed” during various times of the day.

Opening and closing of ductwork and airflow is achieved by zone controls. A zone control is installed in the home which electronically or wirelessly opens and closes “dampers” in the ductwork, depending on the heating demand. You can divert heat to areas of your home using zone control and dampers while decreasing the heating load on your furnace. This type of heating zone control will move heated air to where you want it. Simply put, you are not heating areas of your home that don’t need the heat.

The heating zone controls can be programmed for various times of the day, too. For example, you may not need any heat in your basement while you sleep or when you are away from home. You can program the damper in your basement’s ductwork to remain closed or partially open during these times. In a sense, the heating zone control in your home acts like a programmable thermostat – only it uses a series of dampers to control indoor temperatures.

The next time you walk into an unused part of your home, think about how much money you are spending to heat it. It makes sense to consider heating zone controls. The initial costs of installing zone controls and dampers are minimal and the payback in energy savings and comfort are substantial.

Controls save you money.

Tags: , , , , ,
Posted in Services | Comments Off

How a Furnace Works: A Guide from Holmdel

Wednesday, October 26th, 2011

Do you know how your furnace works? Believe it or not, lots of homeowners in Holmdel probably can’t explain the operation of furnace. It probably isn’t at the top of your “to do” list. It’s only important to know that once you set your thermostat to a desired temperature, the furnace comes on and warms the house.

The most common furnace is fueled by natural gas but there are other examples of heating equipment such as boilers, electric baseboard, or geothermal. But let’s look at how a gas furnace works since natural gas is found in most U.S. households. Gas furnaces use natural gas or propane to provide energy used for generating heat.

When the temperature in your home falls below the level set on the thermostat, an electric pilot light automatically ignites to heat a burner inside the furnace. This burner uses gas to generate heat within a combustion chamber inside the furnace. After the furnace senses that the thermostat has triggered the flame and that it is properly lit, the actual spark (or ignitor) is turned off.

Simultaneously, a motor in the furnace pulls in air from an exchange or return, which could be a grill in the floor, ceiling, or wall of a house. That air flows through ducts into the plenum of the furnace. The plenum is on the opposite side of the heat exchanger from the burner.

Gas will typically burn for at least two minutes before the blower starts to disperse heat throughout your home. This extra time gives the air an adequate period of time to warm up and also so that cold air won’t be pushed through the vents into the rooms in your house at the start. After either the preset time (roughly two minutes) or pre-established temperature is reached, the blower’s motor is turned on and it blows air over the heat exchanger, which usually consists of a series of copper tubes or pipes. When a fan blows air onto the heat exchanger, the air is heated. This heated air is then blown through a series of ducts to heat your home via vents in the floor, walls or ceiling. Exhaust fumes from the combustion process exit the furnace through a gas flue or chimney.

Just as the heat in your home turns on when a certain temperature is reached, it also turns off after the rooms are warm enough, thanks to your thermostat. The thermostat again senses the temperature in the room. When the room warms up to the temperature set by you at the thermostat, the gas valve is switched off, stopping the flow of gas. After the gas is turned off, the blower motor will still run for a few minutes, allowing the heat exchanger to cool off a bit. In some furnaces, the blower motor never shuts off, but operates at low speed to keep air circulating throughout your home.

In a nutshell, your thermostat is the brain in your heating system and your furnace is the brawn, doing most of the work.

Tags: , , , , ,
Posted in Services | Comments Off

« Older Entries